Best Guide Ford Ecosport TPMS Reset Instruction

Best Guide Ford Ecosport TPMS Reset Instruction

||||||||||||||||    WITH STANDARD IGNITION:
1. Inflate all tires to pressure listed on tire placard.
2. Turn ignition to OFF position and press and release brake pedal.
3. Cycle ignition from OFF to RUN position 3 times, ending in RUN position.
4. Press and release brake pedal.
5. Turn ignition to OFF position.
6. Cycle ignition from OFF to RUN position 3 times, ending in RUN position.
7. Horn will sound once and TPMS telltale will blink once train mode is initiated.  If equipped with message center, it will display TRAIN LF TIRE.  Place antennae of learn tool on sidewall of LF tire 180° from valve stem to activate sensor.  Horn will sound once sensor has been recognized.
Repeat step for RF, RR, and LR tires.
8. After training LR tire, the message center will display TRAINING MODE COMPLETE.  If the vehicle is not equipped with the message center display, successful completion can be verified by turning the ignition to the OFF position and not hearing the horn sound.  If the horn sounds, the
training procedure must be repeated.
**WITH INTEGRATED KEY FOB (ACTUAL KEY CONTAINED IN KEY FOB) PUSH-BUTTON
START:
1. With vehicle off, press and release the brake pedal.
2. Using the push button, press and hold the button until the vehicle is in accessory mode (ACC mode). WARNING:  DO NOT PUSH AND RELEASE TOO QUICKLY…PUSH--WAIT FOR SOUND--RELEASE.
3. Power off by pushing the button 1 time.
4. Repeat 2 more times, ending in ACC mode.
5. Press and release the brake pedal, then turn vehicle off.
6. Using the push button, press and hold the button until the vehicle is in accessory mode.
7. Power off by pushing the button 1 time.
8. Repeat 2 more times, ending in ACC mode.
9. Horn will sound once the TPMS telltale will blink once train mode is initiated.  If equipped with message center, it will display TRAIN LF TIRE.
10. Starting at LF tire, decrease air pressure until horn chirps.  Repeat procedure for remaining tires in the following order:  RF, RR, and LR.  If equipped with banded sensors, place antennae of learn tool on sidewall of LF tire 180° from valve stem to activate sensor.  Horn will sound once
sensor has been recognized.  Repeat step for RF, RR, and LR tires.
11. After successfully programming the LR tire, the message center should display "TRAINING COMPLETE."
12. Inflate all tires to pressure listed on tire placard.
***WITH INTELLIGENT ASSIST IGNITION SYSTEM (NO ACTUAL KEY CONTAINED IN KEY FOB): 1. With vehicle off, press and release the brake pedal.
2. Using the push button, press once to turn on, then press again to put vehicle into ACC mode, then press again to turn vehicle off.
3. Repeat 2 more times, ending in ACC mode.
4. Press and release the brake pedal, then turn vehicle off.
5. Using the push button, press once to turn on, then press again to put vehicle into ACC mode, then press again to turn vehicle off.
6. Repeat 2 more times, ending in ACC mode.
7. Horn will sound once and TPMS telltale will blink once train mode is initiated.  If equipped with message center, it will display TRAIN LF TIRE.
8. Starting at LF tire, decrease air pressure until horn chirps.  Repeat procedure for remaining tires in the following order:  RF, RR, and LR.  If equipped with banded sensors, place antennae of learn tool on sidewall of LF tire 180° from valve stem to activate sensor.  Horn will sound once
sensor has been recognized.  Repeat step for RF, RR, and LR tires.
9. After successfully programming the LR tire, the message center should display "TRAINING COMPLETE."
10. Inflate all tires to pressure listed on tire placard.
||||||||||||||||

IF THE ABOVE TUTORIAL FAIL! PLEASE FOLLOW THE INSTRUCTION BELOW! 

• Make sure the vehicle is at a complete stop
• Turn the engine switch off
• Adjust the tire inflation pressure recommended on the tire placard located on the door panel.
• Turn the engine switch to the “ON” position
• Use the information display controls on the steering wheel and highlight Setting Menu
• Press the OK button to choose it
• Select Driver Assist
• Select Tire Monitor and press and hold the OK button until confirmation appears.