2004-2005 Aviator tpms reset

2004-2005 Aviator

Sensor Training

NOTE: The tire pressure monitoring system is not affected by wheel and tire rotation.
NOTE: The tire pressure sensor training procedure must be done on a single vehicle, in an area without radio frequency (RF) noise.
RF noise is generated by electrical motor and appliance operation, cellular telephones, and remote transmitters.

1. Turn the ignition switch to the OFF position.
   
2. Turn the ignition switch from the OFF position to the RUN position three times, ending in the RUN position. Do not wait more than two minutes between each key cycle.
   
3. Press and release the brake pedal.
   
4. Turn the ignition switch to the OFF position.
   
5. Turn the ignition switch from the OFF position to the RUN position three times, ending in the RUN position. Do not wait more than two minutes between each key cycle.

6. When the message center displays "TRAIN LEFT FRONT TIRE", place the magnet on the valve stem of the LF tire pressure sensor. The horn will sound briefly to indicate that the tire pressure sensor has been recognized by the TPMS module.
   
7. Within two minutes after the horn sounds, place the magnet on the valve stem of the RF tire pressure sensor.

NOTE: If the TPMS module does not recognize any one of the five tire pressure sensors during the tire training procedure, the horn will sound twice and the message center will display "TIRE TRAINING MODE INCOMPLETE" and the procedure must be repeated.

8. Repeat Step 7 for the RR, LR, and spare tires.

When the tire training procedure is complete, the horn will sound once and the message center will display "TIRE TRAINING MODE COMPLETE".

1997-2003 A6/A8/S8 all tpms reset

1997-2003 A6/A8/S8 all

If a "low tire pressure" warning light is observed, filling the tire(s) to specified pressures should shut the light off.  If the light remains on follow the below procedure.
The tire pressure monitoring system is operated using the Multi Media Interface (MMI). The system monitors tire pressures that are specified by the operator.  Before hand, the following steps must be performed:

Checking and correcting tire pressures:

• First check and correct all tire pressures on vehicle (including spare tire) Refer to specified tire pressures on tank flap data label.

Saving tire pressures:

After checking the tire pressures and correctly filling the tires, the current pressures must be stored in memory. The system automatically carries out an adaptation procedure.

Proceed as follows:

• Switch ignition on.
  
• Press function key "CAR".
  
• In"CAR" menu, select systems.
  
• Select tire pressure monitoring system.
  
• Select "store tire pressure".

Tire pressures must be stored each time the tire pressure and or tire has been changed.

Further information can be found under "Wheels and Tires : Tire Monitoring System : Service and Repair : Procedures.

Acura cars 2010 above model TPMS Reset

2010 All Models

Reset after tire rotation, flat repair or after sensor replacement

After rotating the tires, repairing a flat tire or replacing a TPMS sensor, drive the vehicle for at least 40 seconds at a speed of 15 mph (24 km/h) or more, and all the sensor ID's will be memorized automatically.

Each sensor is an integrated unit made up of the tire valve stem, a pressure sensor, and a transmitter. The unit is attached to the inside of the wheel, around the valve stem. The sensor transmits internal tire information one time per 60 seconds to the TPMS control unit. When the TPMS control unit receives a tire pressure reading of less than: With 17 inch and 18 inch wheels 175 kPa (1.8 kgf/cm2, 25 psi), or with 19 inch wheels front 202 kPa (2.1 kgf/cm2, 29 psi), rear 175 kPa (1.8 kgf/cm2, 25 psi), the TPMS control unit then turns on the low  tire pressure indicator and the appropriate tire(s) indicator. When that tire's  pressure is increased to more than: With 17 inch and 18 inch wheels 200 kPa (2.0 kgf/cm2, 29 psi),   or with 19 inch wheels front 235 kPa (2.4 kgf/cm2, 34 psi), rear 200 kPa (2.0 kgf/cm2, 29 psi),   the transmitter sends the tire pressure reading to the TPMS control unit, and the TPMS control unit turns the indicators off.

If indicator does not go out, further diagnosis is required.

Acura 2004-2009 all models tpms reset

2004-2009 all models Reset after tire rotation, flat repair or after sensor replacement After rotating the tires, repairing a flat tire or replacing a TPMS sensor, drive the vehicle for at least 40 seconds at a speed of 15 mph (24 km/h) or more, and all the sensor ID's will be memorized automatically. If indicator does not go out, further diagnosis is required.

Honda Civic 2006-2012 Oil Reset Guide

Honda Civic 2006-2012 Oil Reset Guide

---

PLEASE FOLLOW THE QUICK GUIDE BELOW

---

1. Turn ignition to the “RUN” position.
2. Press the “SELECT/RESET” knob until the engine life indicator is displayed.
3. Press the “SELECT/RESET” knob for more than 10 seconds, the indicator and the maintenance code(s) will blink.
4. Press the “SELECT/ RESET” knob for 5 more seconds, the maintenance code(s) will disappear and oil life will be reset to 100.
5. Turn ignition off

 

from WordPress http://ift.tt/2hHma7j
via IFTTT

Honda Civic 2001-2005 Oil Reset Guide

 

---

PLEASE FOLLOW THE SIMPLE INSTRUCTION BELOW!

---

1. Turn ignition off. Press the “SELECT” and “RESET” switches at the same time, and turn to ignition to the “ON” position.
2. Hold switches for at least 10 seconds until the indicator is reset.
3. Turn ignition off

 

from WordPress http://ift.tt/2gTXDMy
via IFTTT

Honda Civic 1990-1996 Oil Reset Guide

 

---

PLEASE FOLLOW THE SIMPLE GUIDE BELOW!

“Insert key into slot below indicator FLag on the lower right corner of the instrument cluster. Push key in until indicator changes from red to green.”

from WordPress http://ift.tt/2hn9I08
via IFTTT

Honda Civic 1997-2000 Oil Reset Guide

---

PLEASE FOLLOW THE INSTRUCTION BELOW!

With reset button on instrument panel:

1. Turn igni-tion off. Press the “SELECT” and “RESET” switches at the same time, and turn to ignition to the “RUN” position.
2. Hold switches for at least 10 seconds until the indicator is reset.
3. Turn ignition off. With key slot in instrument panel: Insert key into slot on the front of the instrument cluster. The indicator will change to green when reset.

from WordPress http://ift.tt/2hnc0wt
via IFTTT

BMW M-Series TPMS Reset Guide - Clever, Fast and Useful

BMW M-Series TPMS Reset Guide - Clever, Fast and Useful

AUTO RELEARN: Ensure all tires are inflated to the pressure listed on the tire placard.  Vehicle
must be driven for at least 10 minutes while maintaining speed above 15mph in order for the
system to learn new sensor IDs.

BMW 7 Series TPMS Reset Tutorial - Its free

BMW 7 Series TPMS Reset Tutorial - Its free

1.Inflate all tires to pressure listed on tire placard.
2.Turn ignition to ON position (engine off).
3.Press and release the MENU button on the EVIC until the message RETRAIN TIRE SENSOR- NO is displayed.   
4.Press the STEP button to select YES.
5.Press the MENU button to start the relearn process. The EVIC will display the message, TRAIN LEFT FRONT TIRE.
6.Starting at LF tire, place relearn magnet over valve stem until horn sounds.
7.After horn sounds, proceed as in step 5 for the next 3 sensors in this order:  RF, RR, LR, SP (if equipped).   
8.Once the EVIC displays the message TRAINING COMPLETE, depress the STEP, C/T, RESET, or MENU buttons to exit the relearn procedure.

BMS 6 Series TPMS Reset Guide - Simple and Effective

BMS 6 Series TPMS Reset Guide - Simple and Effective

1.Inflate all tires to pressure listed on tire placard.
2.Turn ignition to ON position (engine off).
3.Press and release the MENU button on the EVIC until the message RETRAIN TIRE SENSOR- NO is displayed.   
4.Press the STEP button to select YES.
5.Press the MENU button to start the relearn process. The EVIC will display the message, TRAIN LEFT FRONT TIRE.
6.Starting at LF tire, place relearn magnet over valve stem until horn sounds.
7.After horn sounds, proceed as in step 5 for the next 3 sensors in this order:  RF, RR, LR, SP (if equipped).   
8.Once the EVIC displays the message TRAINING COMPLETE, depress the STEP, C/T, RESET, or MENU buttons to exit the relearn procedure.

BMW 5 Series TPMS Reset Tutorial - Fast, Simple and Effective

BMW 5 Series TPMS Reset Tutorial - Fast, Simple and Effective

1.Inflate all tires to pressure listed on tire placard.
2.Turn ignition to ON position (engine off).
3.Press and release the MENU button on the EVIC until the message RETRAIN TIRE SENSOR- NO is displayed.   
4.Press the STEP button to select YES.
5.Press the MENU button to start the relearn process. The EVIC will display the message, TRAIN LEFT FRONT TIRE.
6.Starting at LF tire, place relearn magnet over valve stem until horn sounds.
7.After horn sounds, proceed as in step 5 for the next 3 sensors in this order:  RF, RR, LR, SP (if equipped).   
8.Once the EVIC displays the message TRAINING COMPLETE, depress the STEP, C/T, RESET, or MENU buttons to exit the relearn procedure.

BMW Z-Series TPMS Reset Guide - Quick and Effective

BMW Z-Series TPMS Reset Guide - Quick and Effective

1.Inflate all tires to pressure listed on tire placard.
2.Turn ignition to ON position (engine off).
3.Press and release the MENU button on the EVIC until the message RETRAIN TIRE SENSOR- NO is displayed.   
4.Press the STEP button to select YES.
5.Press the MENU button to start the relearn process. The EVIC will display the message, TRAIN LEFT FRONT TIRE.
6.Starting at LF tire, place relearn magnet over valve stem until horn sounds.
7.After horn sounds, proceed as in step 5 for the next 3 sensors in this order:  RF, RR, LR, SP (if equipped).   
8.Once the EVIC displays the message TRAINING COMPLETE, depress the STEP, C/T, RESET, or MENU buttons to exit the relearn procedure.