Ford Taurus X TPMS Reset Guide
The Ford Taurus X (originally known as Ford Freestyle) is a crossover utility vehicle that was sold by Ford from 2005 to 2009. Essentially the replacement for the Ford Taurus station wagon, the 2005-2007 Freestyle was produced in a single bodystyle with six or seven-passenger seating. As the Taurus made its return for 2008, the Freestyle was rebadged the Taurus X.
Manufactured alongside the Ford Five Hundred, Mercury Montego, Mercury Sable, and the 2008-2009 Ford Taurus, the Ford Freestyle/Taurus X shared the Volvo-derived Ford D3 platform. Front-wheel drive was standard, with all-wheel drive as an option. All versions were produced at Chicago Assembly, in Chicago, Illinois. Unlike the D3 sedans, the Freestyle/Taurus X was sold exclusively as a Ford. Following its discontinuation in 2009, it was not directly replaced, but its role in the Ford line was largely taken over by the larger Ford Flex.
The Taurus X ended production on February 27, 2009 and was marketed in the United States and Canada, as well as South Korea and the U.S. territories of Puerto Rico, U.S. Virgin Islands, and Guam.
1.Inflate all tires to pressure listed on tire placard.
2.Turn ignition to OFF position and press and release brake pedal.
3.Cycle ignition from OFF to RUN position 3 times, ending in RUN position.
4.Press and release brake pedal.
5.Turn ignition to OFF position.
6.Cycle ignition from OFF to RUN position 3 times, ending in RUN position.
7.Horn will sound once and TPMS telltale will blink once train mode is initiated. If equipped with message center, it will display TRAIN LF TIRE. Place antennae of learn tool on sidewall of LF tire 180° from valve stem to activate sensor. Horn will sound once sensor has been recognized. Repeat step for RF, RR, and LR tires.
8.After training LR tire, the message center will display TRAINING MODE COMPLETE. If the vehicle is not equipped with the message center display, successful completion can be verified by turning the ignition to the OFF position and not hearing the horn sound. If the horn sounds, the training procedure must be repeated.
'''''''''WITH INTEGRATED KEY FOB (ACTUAL KEY CONTAINED IN KEY FOB) PUSH-BUTTON START''''''''''''''''''''''''
1.With vehicle off, press and release the brake pedal.
2.Using the push button, press and hold the button until the vehicle is in accessory mode (ACC mode). WARNING: DO NOT PUSH AND RELEASE TOO QUICKLY…PUSH--WAIT FOR SOUND--RELEASE.
3.Power off by pushing the button 1 time.
4.Repeat 2 more times, ending in ACC mode.
5.Press and release the brake pedal, then turn vehicle off.
6.Using the push button, press and hold the button until the vehicle is in accessory mode.
7.Power off by pushing the button 1 time.
8.Repeat 2 more times, ending in ACC mode.
9.Horn will sound once the TPMS telltale will blink once train mode is initiated. If equipped with message center, it will display TRAIN LF TIRE.
10.Starting at LF tire, decrease air pressure until horn chirps. Repeat procedure for remaining tires in the following order: RF, RR, and LR. If equipped with banded sensors, place antennae of learn tool on sidewall of LF tire 180° from valve stem to activate sensor. Horn will sound once sensor has been recognized. Repeat step for RF, RR, and LR tires.
11.After successfully programming the LR tire, the message center should display "TRAINING COMPLETE."
12.Inflate all tires to pressure listed on tire placard.
''''''''''''''''WITH INTELLIGENT ASSIST IGNITION SYSTEM (NO ACTUAL KEY CONTAINED IN KEY FOB)'''''''''''''''''
1.With vehicle off, press and release the brake pedal.
2.Using the push button, press once to turn on, then press again to put vehicle into ACC mode, then press again to turn vehicle off.
3.Repeat 2 more times, ending in ACC mode.
4.Press and release the brake pedal, then turn vehicle off.
5.Using the push button, press once to turn on, then press again to put vehicle into ACC mode, then press again to turn vehicle off.
6.Repeat 2 more times, ending in ACC mode.
7.Horn will sound once and TPMS telltale will blink once train mode is initiated. If equipped with message center, it will display TRAIN LF TIRE.
8.Starting at LF tire, decrease air pressure until horn chirps. Repeat procedure for remaining tires in the following order: RF, RR, and LR. If equipped with banded sensors, place antennae of learn tool on sidewall of LF tire 180° from valve stem to activate sensor. Horn will sound once sensor has been recognized. Repeat step for RF, RR, and LR tires.
9.After successfully programming the LR tire, the message center should display "TRAINING COMPLETE."
10.Inflate all tires to pressure listed on tire placard.
No comments:
Post a Comment