Tpms Reset Hyundai Hyundai Tire Pressure Monitoring System Reset

Tpms Reset Hyundai Hyundai Tire Pressure Monitoring System Reset

 
A Properly Formatted Scan Tool Is Required To Learn New Sensor Ids When Replacing Sensors.

Tia Troubleshooting Tip:
These Vehicles Utilize Two Types Of Tpms: Lo-Line And Hi-Line.
Hi-Line Systems Show The Driver Positions And Air Pressure Of All Tires Via A Display.
Lo-Line Systems Do Not Communicate Position And Will Only Utilize The Tpms Indicator Symbol On The Dash.
Some Models Switched Systems Mid-Year, So Be Aware Of The Type Of Tpms You Are Servicing.

This Instruction of tpms reset is applicable to the following hyundai car model below!
Hyundai Accent 2008-2015
Hyundai Azera  2007-2015
Hyundai Elantra 2008-2016
Hyundai Elantra 2009-2012
Hyundai Elantra 2013-2016
Hyundai Entourage 2007-2010
Hyundai Equus 2011-2015
Hyundai Genesis 2009-2015
Hyundai Genesis 2010-2015
Hyundai Santa 2007-2009
Hyundai Santa 2013-2015
Hyundai Sonata 2007-2015
Hyundai Sonata 2015
Hyundai Tiburon 2007-2008
Hyundai Tucson 2007-2015
Hyundai Veloster 2012-2015
Hyundai Veracruz 2006-2008
Hyundai Veracruz 2008-2012
 

TPMS Reset Honda Tire Pressure Monitoring System Reset

TPMS Reset Honda Tire Pressure Monitoring System Reset

Honda Accord 2008-2012 Tpms Reset - Tire Pressure Monitoring System Reset
 1. A properly formatted scan tool is required to learn new sensor IDs when replacing sensors.
2. After sensor IDs are registered to vehicle, the MIL will flash until the vehicle is driven and the sensors IDs are received by the vehicle.
3. This process could take 1-1 O miles of continuous driving.


Honda Accord 2013-2015 Tpms Reset - Tire Pressure Monitoring System Reset
Models with Information Display:

1. Ensure all tires are inflated to pressure listed on vehicle placard.
2. With manual transmission, ensure the shift lever is in N. For automatic transmission/CVT models, ensure the shift lever is in P.
3. Ignition switch in the ON/RUN position (engine off).
4. Press and hold the TPMS button (located on lower left knee bolster) until the low tire pressure/TPMS indicator blinks twice.
5. If the low tire pressure/TPMS indicator does not blink, confirm the above conditions and hold the TPMS button again. The calibration process finishes automatically.

Models with Multi-information Display

1. Press (UP) (INFO) (DOWN) button to select Vehicle Settings, then press the SEURESET button, and TPMS Calibration appears on the display.
2. Press the SEURESET button. Cancel and Calibrate appear on the screen.
3. Use the up/down arrows from step one to select Calibrate, and then press the SEURESET button.
4. Calibration Started appears on screen, and the calibration process finishes automatically.

Honda Accord Crosstour 2010-2015 Tpms Reset - Tire Pressure Monitoring System Reset
1. A properly formatted scan tool is required to learn new sensor IDs when replacing sensors.
2. After sensor IDs are registered to vehicle, the MIL will flash until the vehicle is driven and the sensors IDs are received by the vehicle.
3. This process could take 1-1 O miles of continuous driving.

Honda Civic 2008-2013 - Tire Pressure Monitoring System Reset
1. A properly formatted scan tool is required to learn new sensor IDs when replacing sensors.
2. After sensor IDs are registered to vehicle, the MIL will flash until the vehicle is driven and the sensors IDs are received by the vehicle.
3. This process could take 1-1 O miles of continuous driving.

Honda Civic 2014-2015 Tpms Reset - Tire Pressure Monitoring System Reset
Models with Information Display:

1. Ensure all tires are inflated to pressure listed on vehicle placard.
2. With manual transmission, ensure the shift lever is in N. For automatic transmission/CVT models, ensure the shift lever is in P.
3. Ignition switch in the ON/RUN position (engine off).
4. Press and hold the TPMS button (located on lower left knee bolster) until the low tire pressure/TPMS indicator blinks twice.
5. If the low tire pressure/TPMS indicator does not blink, confirm the above conditions and hold the TPMS button again. The calibration process finishes automatically.

Models with Multi-information Display

1. Press (UP) (INFO) (DOWN) button to select Vehicle Settings, then press the SEURESET button, and TPMS Calibration appears on the display.
2. Press the SEURESET button. Cancel and Calibrate appear on the screen.
3. Use the up/down arrows from step one to select Calibrate, and then press the SEURESET button.
4. Calibration Started appears on screen, and the calibration process finishes automatically.

Honda Crosstour 2010-2015 Tpms Reset - Tire Pressure Monitoring System Reset
1. A properly formatted scan tool is required to learn new sensor IDs when replacing sensors.
2. After sensor IDs are registered to vehicle, the MIL will flash until the vehicle is driven and the sensors IDs are received by the vehicle.
3. This process could take 1-1 O miles of continuous driving.

Honda Crosstour 2010-2015 Tpms Reset - Tire Pressure Monitoring System Reset
1. A properly formatted scan tool is required to learn new sensor IDs when replacing sensors.
2. After sensor IDs are registered to vehicle, the MIL will flash until the vehicle is driven and the sensors IDs are received by the vehicle.
3. This process could take 1-1 O miles of continuous driving.

Honda CR-V 2007-2013 Tpms Reset - Tire Pressure Monitoring System Reset
1. A properly formatted scan tool is required to learn new sensor IDs when replacing sensors.
2. After sensor IDs are registered to vehicle, the MIL will flash until the vehicle is driven and the sensors IDs are received by the vehicle.
3. This process could take 1-1 O miles of continuous driving.

Honda CR-Z 2011-2015 Tpms Reset - Tire Pressure Monitoring System Reset
Models with Information Display:

1. Ensure all tires are inflated to pressure listed on vehicle placard.
2. With manual transmission, ensure the shift lever is in N. For automatic transmission/CVT models, ensure the shift lever is in P.
3. Ignition switch in the ON/RUN position (engine off).
4. Press and hold the TPMS button (located on lower left knee bolster) until the low tire pressure/TPMS indicator blinks twice.
5. If the low tire pressure/TPMS indicator does not blink, confirm the above conditions and hold the TPMS button again. The calibration process finishes automatically.

Models with Multi-information Display

1. Press (UP) (INFO) (DOWN) button to select Vehicle Settings, then press the SEURESET button, and TPMS Calibration appears on the display.
2. Press the SEURESET button. Cancel and Calibrate appear on the screen.
3. Use the up/down arrows from step one to select Calibrate, and then press the SEURESET button.
4. Calibration Started appears on screen, and the calibration process finishes automatically.

Honda Element 2006-2008 Tpms Reset - Tire Pressure Monitoring System Reset
1. A properly formatted scan tool is required to learn new sensor IDs when replacing sensors.
2. After sensor IDs are registered to vehicle, the MIL will flash until the vehicle is driven and the sensors IDs are received by the vehicle.
3. This process could take 1-1 O miles of continuous driving.

Honda Fit  2015 Tpms Reset - Tire Pressure Monitoring System Reset
Models with Information Display:

1. Ensure all tires are inflated to pressure listed on vehicle placard.
2. With manual transmission, ensure the shift lever is in N. For automatic transmission/CVT models, ensure the shift lever is in P.
3. Ignition switch in the ON/RUN position (engine off).
4. Press and hold the TPMS button (located on lower left knee bolster) until the low tire pressure/TPMS indicator blinks twice.
5. If the low tire pressure/TPMS indicator does not blink, confirm the above conditions and hold the TPMS button again. The calibration process finishes automatically.

Models with Multi-information Display

1. Press (UP) (INFO) (DOWN) button to select Vehicle Settings, then press the SEURESET button, and TPMS Calibration appears on the display.
2. Press the SEURESET button. Cancel and Calibrate appear on the screen.
3. Use the up/down arrows from step one to select Calibrate, and then press the SEURESET button.
4. Calibration Started appears on screen, and the calibration process finishes automatically.

Honda Fit 2008-2014 Tpms Reset - Tire Pressure Monitoring System Reset
1. A properly formatted scan tool is required to learn new sensor IDs when replacing sensors.
2. After sensor IDs are registered to vehicle, the MIL will flash until the vehicle is driven and the sensors IDs are received by the vehicle.
3. This process could take 1-1 O miles of continuous driving.

Honda Insight 2010-2014 Tpms Reset - Tire Pressure Monitoring System Reset
1. A properly formatted scan tool is required to learn new sensor IDs when replacing sensors.
2. After sensor IDs are registered to vehicle, the MIL will flash until the vehicle is driven and the sensors IDs are received by the vehicle.
3. This process could take 1-1 O miles of continuous driving.

Honda Odyssey  2007-2010 Tpms Reset - Tire Pressure Monitoring System Reset
1. A properly formatted scan tool is required to learn new sensor IDs when replacing sensors.
2. After sensor IDs are registered to vehicle, the MIL will flash until the vehicle is driven and the sensors IDs are received by the vehicle.
3. This process could take 1-1 O miles of continuous driving.

Honda Odyssey  2008-2010 Tpms Reset - Tire Pressure Monitoring System Reset
Ensure all tires are inflated to the pressure listed on the tire placard.
Drive vehicle at speeds above 15 mph for a minimum of 40 seconds. Sensor ID's will be learned automatically.
This process could take 1-10 miles of continuous driving.

Honda Odyssey 2005-2007 Tpms Reset - Tire Pressure Monitoring System Reset
1. A properly formatted scan tool is required to learn new sensor IDs when replacing sensors.
2. After sensor IDs are registered to vehicle, the MIL will flash until the vehicle is driven and the sensors IDs are received by the vehicle.
3. This process could take 1-1 O miles of continuous driving.

Honda Odyssey 2011-2015 Tpms Reset - Tire Pressure Monitoring System Reset
1. A properly formatted scan tool is required to learn new sensor IDs when replacing sensors.
2. After sensor IDs are registered to vehicle, the MIL will flash until the vehicle is driven and the sensors IDs are received by the vehicle.
3. This process could take 1-1 O miles of continuous driving.

Honda Pilot 2005-2008 Tpms Reset - Tire Pressure Monitoring System Reset
Ensure all tires are inflated to the pressure listed on the tire placard.
Drive vehicle at speeds above 15 mph for a minimum of 40 seconds. Sensor ID's will be learned automatically.
This process could take 1-10 miles of continuous driving.

Honda Pilot 2009-2015 Tpms Reset - Tire Pressure Monitoring System Reset
1. A properly formatted scan tool is required to learn new sensor IDs when replacing sensors.
2. After sensor IDs are registered to vehicle, the MIL will flash until the vehicle is driven and the sensors IDs are received by the vehicle.
3. This process could take 1-1 O miles of continuous driving.

Honda Ridgeline 2006-2014 Tpms Reset - Tire Pressure Monitoring System Reset
Ensure all tires are inflated to the pressure listed on the tire placard.
Drive vehicle at speeds above 15 mph for a minimum of 40 seconds. Sensor ID's will be learned automatically.
This process could take 1-10 miles of continuous driving.

Honda S2000 2008-2009 Tpms Reset - Tire Pressure Monitoring System Reset
1. A properly formatted scan tool is required to learn new sensor IDs when replacing sensors.
2. After sensor IDs are registered to vehicle, the MIL will flash until the vehicle is driven and the sensors IDs are received by the vehicle.
3. This process could take 1-1 O miles of continuous driving.

TPMS Reset Freightliner Sprinter Tire Pressure Monitoring System Reset Guide

TPMS Reset Freightliner Sprinter Tire Pressure Monitoring System Reset Guide

Freightliner Sprinter 2007-2014 TPMS Reset Tire Pressure Monitoring System Reset

Reset Air Pressure

1. Inflate all tires to pressure indicated on tire placard.
2. Turn ignition to ON/RUN position (engine off).
3. Press forward/back button on steering wheel until trip and odometer are displayed.
4. Press UP/DOWN button until tire inflation pressure monitor is displayed.
5. Hold down reset button (located on instrument cluster) until MONITOR CURRENT TIRE PRESSURE? is displayed.
6. Press+ button, TIRE PRESS. MONITOR-ACTIVATED!-PRESS. DISPLAY AFTER DRIVING A FEW MINS. is displayed.
7. If REACTIVATE-TIRE PRESS. MONITOR! appears, repeat relearn procedure.
8. If TIRE PRESSURE-CHECK TIRES! appears, indicates tire pressure too low, adjust pressures accordingly.

Relearn New Sensor IDs

1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Vehicle must be driven for at least 1 o minutes while maintaining speed above 15mph in order for system to learn new sensor IDs.
3. If spare tire sensor ID is being programmed, a properly formatted scan tool is necessary.

TPMS Reset Bentley Tire Pressure Monitoring System Reset

TPMS Reset Bentley Tire Pressure Monitoring System Reset

TPMS Reset Bentley Azure 2007-2014 Tpms Reset Tire Pressure Monitoring System Reset
1. Inflate all tires to pressures listed on tire placard.
2. Press the "VEHICLE" function key on the instrument cluster. Follow any prompts to complete procedure.
3. Drive vehicle above 30mph for at least 15 minutes.

TPMS Reset Bentley Flying Spur 2005-2015 Tpms Reset Tire Pressure Monitoring System Reset
1. Inflate all tires to pressures listed on tire placard.
2. Press the "VEHICLE" function key on the instrument cluster. Follow any prompts to complete procedure.
3. Drive vehicle above 30mph for at least 15 minutes.

TPMS Reset Bentley GT 2006-2015 Tpms Reset Tire Pressure Monitoring System Reset
1. Inflate all tires to pressures listed on tire placard.
2. Press the "VEHICLE" function key on the instrument cluster. Follow any prompts to complete procedure.
3. Drive vehicle above 30mph for at least 15 minutes.

TPMS Reset Bentley GTC 2012-2014 Tpms Reset Tire Pressure Monitoring System Reset
1. Inflate all tires to pressures listed on tire placard.
2. Press the "VEHICLE" function key on the instrument cluster. Follow any prompts to complete procedure.
3. Drive vehicle above 30mph for at least 15 minutes.

TPMS Reset Bentley Mulsanne 2011-2015 Tpms Reset Tire Pressure Monitoring System Reset
1. Inflate all tires to pressures listed on tire placard.
2. Press the "VEHICLE" function key on the instrument cluster. Follow any prompts to complete procedure.
3. Drive vehicle above 30mph for at least 15 minutes.

TPMS Reset- Bmw Cars Tpms Reset Guide

TPMS Reset- Bmw Cars Tpms Reset Guide

QUICK INFOMATION ABOUT BMW MANUFACTURER:

BMW  

Bayerische Motoren Werke

BMW AG is a Germany-based company which currently produces automobiles and motorcycles, and produced aircraft engines until 1945.

The company was founded in 1916 and has its headquarters in Munich, Bavaria. BMW produces motor vehicles in Germany, Brazil, China, India, South Africa and the United States. In 2015, BMW was the world's twelfth largest producer of motor vehicles, with 2,279,503 vehicles produced.The Quandt family are long-term shareholders of the company, with the remaining stocks owned by public float.

Automobiles are marketed under the brands BMW (with sub-brands BMW M for performance models and BMW i for plug-in electric cars), Mini and Rolls-Royce. Motorcycles are marketed under the brand BMW Motorrad.

The company has significant motorsport history, especially in touring cars, Formula 1, sports cars and the Isle of Man TT.

BELOW ARE THE TPMS INSTRUCTION BASE OF MODEL AND YEAR MODEL

TPMS RESET BMW 1 Series 2008-2013 Tire Pressure Monitoring System Reset Guide
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select "Settings" or "Vehicle Info".
4. Select "Vehicle", "Vehicle/Tires" or "Vehicle Status".
5. Select "TPM", "Reset TPM", or "Perform Reset".
6. Start the engine, select "Reset", "Yes".
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and "RESET" are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until "RESETIING" or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

TPMS RESET BMW 2 Series 2014 Tire Pressure Monitoring System Reset Guide
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select "Settings" or "Vehicle Info".
4. Select "Vehicle", "Vehicle/Tires" or "Vehicle Status".
5. Select "TPM", "Reset TPM", or "Perform Reset".
6. Start the engine, select "Reset", "Yes".
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and "RESET" are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until "RESETIING" or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

TPMS RESET BMW 2 Series 2014-2015 Tire Pressure Monitoring System Reset Guide
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select "Settings" or "Vehicle Info".
4. Select "Vehicle", "Vehicle/Tires" or "Vehicle Status".
5. Select "TPM", "Reset TPM", or "Perform Reset".
6. Start the engine, select "Reset", "Yes".
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and "RESET" are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until "RESETIING" or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

TPMS RESET BMW 3 Series2007-2011 Tire Pressure Monitoring System Reset Guide
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select "Settings" or "Vehicle Info".
4. Select "Vehicle", "Vehicle/Tires" or "Vehicle Status".
5. Select "TPM", "Reset TPM", or "Perform Reset".
6. Start the engine, select "Reset", "Yes".
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and "RESET" are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until "RESETIING" or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

TPMS RESET BMW 3 Series 2 door/wagon 2012-2013 Tire Pressure Monitoring System Reset Guide
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select "Settings" or "Vehicle Info".
4. Select "Vehicle", "Vehicle/Tires" or "Vehicle Status".
5. Select "TPM", "Reset TPM", or "Perform Reset".
6. Start the engine, select "Reset", "Yes".
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and "RESET" are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until "RESETIING" or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

TPMS RESET BMW 3 Series 4 door sedan 2014 Tire Pressure Monitoring System Reset Guide
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select "Settings" or "Vehicle Info".
4. Select "Vehicle", "Vehicle/Tires" or "Vehicle Status".
5. Select "TPM", "Reset TPM", or "Perform Reset".
6. Start the engine, select "Reset", "Yes".
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and "RESET" are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until "RESETIING" or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

TPMS RESET BMW 3 Series 2014-2015 Tire Pressure Monitoring System Reset Guide
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select "Settings" or "Vehicle Info".
4. Select "Vehicle", "Vehicle/Tires" or "Vehicle Status".
5. Select "TPM", "Reset TPM", or "Perform Reset".
6. Start the engine, select "Reset", "Yes".
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and "RESET" are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until "RESETIING" or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

TPMS RESET BMW 4 Series 2014 Tire Pressure Monitoring System Reset Guide
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select "Settings" or "Vehicle Info".
4. Select "Vehicle", "Vehicle/Tires" or "Vehicle Status".
5. Select "TPM", "Reset TPM", or "Perform Reset".
6. Start the engine, select "Reset", "Yes".
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and "RESET" are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until "RESETIING" or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

TPMS RESET BMW 4 Series 2014-2015 Tire Pressure Monitoring System Reset Guide
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select "Settings" or "Vehicle Info".
4. Select "Vehicle", "Vehicle/Tires" or "Vehicle Status".
5. Select "TPM", "Reset TPM", or "Perform Reset".
6. Start the engine, select "Reset", "Yes".
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and "RESET" are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until "RESETIING" or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

TPMS RESET BMW 5 Series 2006-2011 Tire Pressure Monitoring System Reset Guide
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select "Settings" or "Vehicle Info".
4. Select "Vehicle", "Vehicle/Tires" or "Vehicle Status".
5. Select "TPM", "Reset TPM", or "Perform Reset".
6. Start the engine, select "Reset", "Yes".
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and "RESET" are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until "RESETIING" or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

TPMS RESET BMW 5 Series 2011-2014 Tire Pressure Monitoring System Reset Guide
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select "Settings" or "Vehicle Info".
4. Select "Vehicle", "Vehicle/Tires" or "Vehicle Status".
5. Select "TPM", "Reset TPM", or "Perform Reset".
6. Start the engine, select "Reset", "Yes".
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and "RESET" are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until "RESETIING" or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

TPMS RESET BMW 5 Series 2015 Tire Pressure Monitoring System Reset Guide
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select "Settings" or "Vehicle Info".
4. Select "Vehicle", "Vehicle/Tires" or "Vehicle Status".
5. Select "TPM", "Reset TPM", or "Perform Reset".
6. Start the engine, select "Reset", "Yes".
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and "RESET" are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until "RESETIING" or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

TPMS RESET BMW 6 Series 2006-2015 Tire Pressure Monitoring System Reset Guide
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select "Settings" or "Vehicle Info".
4. Select "Vehicle", "Vehicle/Tires" or "Vehicle Status".
5. Select "TPM", "Reset TPM", or "Perform Reset".
6. Start the engine, select "Reset", "Yes".
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and "RESET" are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until "RESETIING" or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

TPMS RESET BMW 7 Series 2006-2011 Tire Pressure Monitoring System Reset Guide
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select "Settings" or "Vehicle Info".
4. Select "Vehicle", "Vehicle/Tires" or "Vehicle Status".
5. Select "TPM", "Reset TPM", or "Perform Reset".
6. Start the engine, select "Reset", "Yes".
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and "RESET" are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until "RESETIING" or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

TPMS RESET BMW 7 Series 2011-2014 Tire Pressure Monitoring System Reset Guide
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select "Settings" or "Vehicle Info".
4. Select "Vehicle", "Vehicle/Tires" or "Vehicle Status".
5. Select "TPM", "Reset TPM", or "Perform Reset".
6. Start the engine, select "Reset", "Yes".
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and "RESET" are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until "RESETIING" or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

TPMS RESET BMW 7 Series 2015 Tire Pressure Monitoring System Reset Guide
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select "Settings" or "Vehicle Info".
4. Select "Vehicle", "Vehicle/Tires" or "Vehicle Status".
5. Select "TPM", "Reset TPM", or "Perform Reset".
6. Start the engine, select "Reset", "Yes".
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and "RESET" are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until "RESETIING" or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

TPMS RESET BMW Alpina 2004-2014 Tire Pressure Monitoring System Reset Guide
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select "Settings" or "Vehicle Info".
4. Select "Vehicle", "Vehicle/Tires" or "Vehicle Status".
5. Select "TPM", "Reset TPM", or "Perform Reset".
6. Start the engine, select "Reset", "Yes".
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and "RESET" are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until "RESETIING" or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

TPMS RESET BMW I3 2014-2015 Tire Pressure Monitoring System Reset Guide
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select "Settings" or "Vehicle Info".
4. Select "Vehicle", "Vehicle/Tires" or "Vehicle Status".
5. Select "TPM", "Reset TPM", or "Perform Reset".
6. Start the engine, select "Reset", "Yes".
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and "RESET" are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until "RESETIING" or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

TPMS RESET BMW I8 2014-2015 Tire Pressure Monitoring System Reset Guide
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select "Settings" or "Vehicle Info".
4. Select "Vehicle", "Vehicle/Tires" or "Vehicle Status".
5. Select "TPM", "Reset TPM", or "Perform Reset".
6. Start the engine, select "Reset", "Yes".
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and "RESET" are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until "RESETIING" or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

TPMS RESET BMW M3 2008-2013 Tire Pressure Monitoring System Reset Guide
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select "Settings" or "Vehicle Info".
4. Select "Vehicle", "Vehicle/Tires" or "Vehicle Status".
5. Select "TPM", "Reset TPM", or "Perform Reset".
6. Start the engine, select "Reset", "Yes".
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and "RESET" are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until "RESETIING" or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

TPMS RESET BMW M5 2006-2011 Tire Pressure Monitoring System Reset Guide
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select "Settings" or "Vehicle Info".
4. Select "Vehicle", "Vehicle/Tires" or "Vehicle Status".
5. Select "TPM", "Reset TPM", or "Perform Reset".
6. Start the engine, select "Reset", "Yes".
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and "RESET" are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until "RESETIING" or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

TPMS RESET BMW M6 2006-2011 Tire Pressure Monitoring System Reset Guide
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select "Settings" or "Vehicle Info".
4. Select "Vehicle", "Vehicle/Tires" or "Vehicle Status".
5. Select "TPM", "Reset TPM", or "Perform Reset".
6. Start the engine, select "Reset", "Yes".
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and "RESET" are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until "RESETIING" or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.


TPMS RESET BMW M6 2011-2014 Tire Pressure Monitoring System Reset Guide
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select "Settings" or "Vehicle Info".
4. Select "Vehicle", "Vehicle/Tires" or "Vehicle Status".
5. Select "TPM", "Reset TPM", or "Perform Reset".
6. Start the engine, select "Reset", "Yes".
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and "RESET" are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until "RESETIING" or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

TPMS RESET BMW X1 2013-2015 Tire Pressure Monitoring System Reset Guide
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select "Settings" or "Vehicle Info".
4. Select "Vehicle", "Vehicle/Tires" or "Vehicle Status".
5. Select "TPM", "Reset TPM", or "Perform Reset".
6. Start the engine, select "Reset", "Yes".
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and "RESET" are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until "RESETIING" or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

TPMS RESET BMW X3 2006-2014 Tire Pressure Monitoring System Reset Guide
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select "Settings" or "Vehicle Info".
4. Select "Vehicle", "Vehicle/Tires" or "Vehicle Status".
5. Select "TPM", "Reset TPM", or "Perform Reset".
6. Start the engine, select "Reset", "Yes".
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and "RESET" are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until "RESETIING" or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

TPMS RESET BMW X3 2015 Tire Pressure Monitoring System Reset Guide
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select "Settings" or "Vehicle Info".
4. Select "Vehicle", "Vehicle/Tires" or "Vehicle Status".
5. Select "TPM", "Reset TPM", or "Perform Reset".
6. Start the engine, select "Reset", "Yes".
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and "RESET" are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until "RESETIING" or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

TPMS RESET BMW X4 2015 Tire Pressure Monitoring System Reset Guide
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select "Settings" or "Vehicle Info".
4. Select "Vehicle", "Vehicle/Tires" or "Vehicle Status".
5. Select "TPM", "Reset TPM", or "Perform Reset".
6. Start the engine, select "Reset", "Yes".
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and "RESET" are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until "RESETIING" or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

TPMS RESET BMW X5 2007-2011 Tire Pressure Monitoring System Reset Guide
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select "Settings" or "Vehicle Info".
4. Select "Vehicle", "Vehicle/Tires" or "Vehicle Status".
5. Select "TPM", "Reset TPM", or "Perform Reset".
6. Start the engine, select "Reset", "Yes".
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and "RESET" are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until "RESETIING" or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

TPMS RESET BMW X5 2011-2013 Tire Pressure Monitoring System Reset Guide
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select "Settings" or "Vehicle Info".
4. Select "Vehicle", "Vehicle/Tires" or "Vehicle Status".
5. Select "TPM", "Reset TPM", or "Perform Reset".
6. Start the engine, select "Reset", "Yes".
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and "RESET" are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until "RESETIING" or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

TPMS RESET BMW X5 2014-2015 Tire Pressure Monitoring System Reset Guide
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select "Settings" or "Vehicle Info".
4. Select "Vehicle", "Vehicle/Tires" or "Vehicle Status".
5. Select "TPM", "Reset TPM", or "Perform Reset".
6. Start the engine, select "Reset", "Yes".
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and "RESET" are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until "RESETIING" or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

TPMS RESET BMW X6 2008-2011 Tire Pressure Monitoring System Reset Guide
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select "Settings" or "Vehicle Info".
4. Select "Vehicle", "Vehicle/Tires" or "Vehicle Status".
5. Select "TPM", "Reset TPM", or "Perform Reset".
6. Start the engine, select "Reset", "Yes".
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and "RESET" are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until "RESETIING" or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

TPMS RESET BMW X6 2011-2014 Tire Pressure Monitoring System Reset Guide
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select "Settings" or "Vehicle Info".
4. Select "Vehicle", "Vehicle/Tires" or "Vehicle Status".
5. Select "TPM", "Reset TPM", or "Perform Reset".
6. Start the engine, select "Reset", "Yes".
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and "RESET" are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until "RESETIING" or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

TPMS RESET BMW X6 2015 Tire Pressure Monitoring System Reset Guide
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select "Settings" or "Vehicle Info".
4. Select "Vehicle", "Vehicle/Tires" or "Vehicle Status".
5. Select "TPM", "Reset TPM", or "Perform Reset".
6. Start the engine, select "Reset", "Yes".
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and "RESET" are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until "RESETIING" or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

TPMS RESET BMW Z Series 2007-2011 Tire Pressure Monitoring System Reset Guide
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select "Settings" or "Vehicle Info".
4. Select "Vehicle", "Vehicle/Tires" or "Vehicle Status".
5. Select "TPM", "Reset TPM", or "Perform Reset".
6. Start the engine, select "Reset", "Yes".
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and "RESET" are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until "RESETIING" or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

TPMS RESET BMW Z Series 2011-2014 Tire Pressure Monitoring System Reset Guide
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select "Settings" or "Vehicle Info".
4. Select "Vehicle", "Vehicle/Tires" or "Vehicle Status".
5. Select "TPM", "Reset TPM", or "Perform Reset".
6. Start the engine, select "Reset", "Yes".
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and "RESET" are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until "RESETIING" or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

TPMS RESET BMW Z4 2014 Tire Pressure Monitoring System Reset Guide
IF EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Turn ignition to the ON position (engine off).
3. Using the iDrive controller, select "Settings" or "Vehicle Info".
4. Select "Vehicle", "Vehicle/Tires" or "Vehicle Status".
5. Select "TPM", "Reset TPM", or "Perform Reset".
6. Start the engine, select "Reset", "Yes".
7. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE:
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Move turn signal toggle switch up or down until TPMS indicator and "RESET" are displayed.
4. Press button at end of turn signal lever.
5. Press and hold button at end of turn signal lever until "RESETIING" or a checkmark is displayed.
6. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

IF NOT EQUIPPED WITH IDRIVE (FOR SOME MODELS):
1. Ensure all tires are inflated to the pressure listed on the tire placard.
2. Start engine.
3. Hold down the TPMS Reset button (located under the hazards button or in front of the gear selector) until the TPMS light in the gauge cluster illuminates. Button may use initials ROE on some models.
4. Vehicle must be driven for up to 20 minutes above 20mph to complete relearn.

TPMS Reset - Audi Cars TPMS Reset Guide

TPMS Reset - Audi Cars Tire Pressure Monitoring System Reset Guide

 QUICK INFORMATION ABOUT THIS CAR MANUFACTURER.

Audi AG is a German automobile manufacturer that designs, engineers, produces, markets and distributes luxury vehicles. Audi is a member of the Volkswagen Group and has its roots at Ingolstadt, Bavaria, Germany. Audi-branded vehicles are produced in nine production facilities worldwide.

The origins of the company are complex, going back to the early 20th century and the initial enterprises (Horch and the Audiwerke) founded by engineer August Horch; and two other manufacturers (DKW and Wanderer), leading to the foundation of Auto Union in 1932. The modern era of Audi essentially began in the 1960s when Auto Union was acquired by Volkswagen from Daimler-Benz. After relaunching the Audi brand with the 1965 introduction of the Audi F103 series, Volkswagen merged Auto Union with NSU Motorenwerke in 1969, thus creating the present day form of the company.

The company name is based on the Latin translation of the surname of the founder, August Horch. "Horch", meaning "listen" in German, becomes "audi" in Latin. The four rings of the Audi logo each represent one of four car companies that banded together to create Audi's predecessor company, Auto Union. Audi's slogan is Vorsprung durch Technik, meaning "Advancement through Technology". However, Audi USA had used the slogan "Truth in Engineering" from 2007 to 2016, and have not used the slogan since 2016. Audi, along with BMW and Mercedes-Benz, are among the best-selling luxury automobile brands in the world.

Audi A3 2006-2011 TPMS Reset Tire Pressure Monitoring System Reset
1. Inflate all tires to pressure indicated on tire placard.
2. Turn ignition to ON/RUN position (engine off).
3. Hold down the "SET" button located between the A/C and radio controls, or near the gear selector until a chime is heard.
4. Drive vehicle above 30mph for at least 30 minutes.


Audi A4 2012-2014 TPMS Reset Tire Pressure Monitoring System Reset
1. Inflate all tires to pressure indicated on tire placard.
2. Turn ignition to ON/RUN position (engine off).
3. Press CAR or MENU button by the gear selector.
4. Rotate MENU knob to position arrow by SET, Tire Pressure Monitoring, or Car (depending on exact model trim).
5. Press MENU knob.
6. Move arrow to TIRE PRESSURE, only if selecting the Car option mentioned in Step 4.
7. Press MENU knob.
8. Move arrow to STORE PRESSURES.
9. Press MENU knob, a check mark will appear to signal relearn completion.
10.Exit out of tire menu. Vehicle will need to be driven several minutes to complete relearn process.


Audi A4 Cabrio 2003-2012 TPMS Reset Tire Pressure Monitoring System Reset
1. Inflate all tires to pressure listed on tire placard.
2. Press CAR function button, or select "SET" on the driver's information screen.
3. Select TIRE PRESSURE MONITORING.
4. Select WHEEL CHANGE (select STORE CURR TIRE PRESSURES if resetting tire pressures).
5. Relearn can take 20 minutes to complete.


Audi A4 4 Door 2009-2012 TPMS Reset Tire Pressure Monitoring System Reset
1. Inflate all tires to pressure listed on tire placard.
2. Hold down RESET button (on end of wiper lever) until DISPLAY TYPE is displayed.
3. Press button on end of wiper lever to select SET.
4. Press RESET button.
5. Press button on end of wiper lever to select TIRE PRESSURE
6. Press RESET button.
7. Press button on end of wiper lever to select WHEEL CHANGE (select STORE PRESSURES if resetting air pressure).
8. Press RESET button. Relearn can take 20 minutes to complete.


Audi A4 & S4 2012-2015 TPMS Reset Tire Pressure Monitoring System Reset
1. Inflate all tires to pressure indicated on tire placard.
2. Turn ignition to ON/RUN position (engine off).
3. Press CAR or MENU button by the gear selector.
4. Rotate MENU knob to position arrow by SET, Tire Pressure Monitoring, or Car (depending on exact model trim).
5. Press MENU knob.
6. Move arrow to TIRE PRESSURE, only if selecting the Car option mentioned in Step 4.
7. Press MENU knob.
8. Move arrow to STORE PRESSURES.
9. Press MENU knob, a check mark will appear to signal relearn completion.
10.Exit out of tire menu. Vehicle will need to be driven several minutes to complete relearn process.


Audi A5 & S5 2008-2012 TPMS Reset Tire Pressure Monitoring System Reset
1. Inflate all tires to pressure listed on tire placard.
2. Turn ignition to ON/RUN position (engine off).
3. Press CAR function button.
4. Select TIRE PRESSURE MONITORING.
5. Select INITIALIZE WHEELS (select STORE CURR TIRE PRESSURES if resetting tire pressures).
6. Relearn can take 20 minutes to complete.


Audi A5 & S5 2012-2015 TPMS Reset Tire Pressure Monitoring System Reset
METHOD 1
1. Inflate all tires to pressure indicated on tire placard.
2. Turn ignition to ON/RUN position (engine off).
3. Press CAR or MENU button by the gear selector.
4. Rotate MENU knob to position arrow by SET, Tire Pressure Monitoring, or Car (depending on exact model trim).
5. Press MENU knob.
6. Move arrow to TIRE PRESSURE, only if selecting the Car option mentioned in Step 4.
7. Press MENU knob.
8. Move arrow to STORE PRESSURES.
9. Press MENU knob, a check mark will appear to signal relearn completion.
10.Exit out of tire menu. Vehicle will need to be driven several minutes to complete relearn process.
METHOD 2
1. Inflate all tires to pressure indicated on tire placard.
2. Turn ignition to ON/RUN position (engine off).
3. Enter tire pressure mode.
4. Press media control, located on center console.
5. Let vehicle sit for 20 minutes.
6. After 20 minutes, vehicle must be driven above 25mph for 10 minutes.


Audi A6 & S6 2005-2012 TPMS Reset Tire Pressure Monitoring System Reset
1. Inflate all tires to pressure indicated on tire placard.
2. Turn ignition to ON/RUN position (engine off).
3. Press CAR or MENU button by the gear selector.
4. Rotate MENU knob to position arrow by SET, Tire Pressure Monitoring, or Car (depending on exact model trim).
5. Press MENU knob.
6. Move arrow to TIRE PRESSURE, only if selecting the Car option mentioned in Step 4.
7. Press MENU knob.
8. Move arrow to STORE PRESSURES.
9. Press MENU knob, a check mark will appear to signal relearn completion.
10.Exit out of tire menu. Vehicle will need to be driven several minutes to complete relearn process.


Audi A6 & s6 2009-2015 TPMS Reset Tire Pressure Monitoring System Reset
1. Inflate all tires to pressure indicated on tire placard.
2. Turn ignition to ON/RUN position (engine off).
3. Press CAR or MENU button by the gear selector.
4. Rotate MENU knob to position arrow by SET, Tire Pressure Monitoring, or Car (depending on exact model trim).
5. Press MENU knob.
6. Move arrow to TIRE PRESSURE, only if selecting the Car option mentioned in Step 4.
7. Press MENU knob.
8. Move arrow to STORE PRESSURES.
9. Press MENU knob, a check mark will appear to signal relearn completion.
10.Exit out of tire menu. Vehicle will need to be driven several minutes to complete relearn process.


Audi A8 2004-2011 TPMS Reset Tire Pressure Monitoring System Reset
1. Inflate all tires to pressure listed on tire placard.
2. Turn ignition to ON/RUN position (engine off).
3. Press CAR function button.
4. Select TIRE PRESSURE MONITORING.
5. Select INITIALIZE WHEELS (select STORE CURR TIRE PRESSURES if resetting tire pressures).
6. Relearn can take 20 minutes to complete.


Audi A8-S8 2010-2015 TPMS Reset Tire Pressure Monitoring System Reset
1. Inflate all tires to pressure indicated on tire placard.
2. Turn ignition to ON/RUN position (engine off).
3. Press CAR or MENU button by the gear selector.
4. Rotate MENU knob to position arrow by SET, Tire Pressure Monitoring, or Car (depending on exact model trim).
5. Press MENU knob.
6. Move arrow to TIRE PRESSURE, only if selecting the Car option mentioned in Step 4.
7. Press MENU knob.
8. Move arrow to STORE PRESSURES.
9. Press MENU knob, a check mark will appear to signal relearn completion.
10.Exit out of tire menu. Vehicle will need to be driven several minutes to complete relearn process.


Audi Q5 2009-2012 TPMS Reset Tire Pressure Monitoring System Reset
1. Inflate all tires to pressure listed on tire placard.
2. Turn ignition to ON/RUN position (engine off).
3. Press CAR function button.
4. Select TIRE PRESSURE MONITORING.
5. Select INITIALIZE WHEELS (select STORE CURR TIRE PRESSURES if resetting tire pressures).
6. Relearn can take 20 minutes to complete.


Audi Q5 2009-2015 TPMS Reset Tire Pressure Monitoring System Reset
1. Inflate all tires to pressure indicated on tire placard.
2. Turn ignition to ON/RUN position (engine off).
3. Press CAR or MENU button by the gear selector.
4. Rotate MENU knob to position arrow by SET, Tire Pressure Monitoring, or Car (depending on exact model trim).
5. Press MENU knob.
6. Move arrow to TIRE PRESSURE, only if selecting the Car option mentioned in Step 4.
7. Press MENU knob.
8. Move arrow to STORE PRESSURES.
9. Press MENU knob, a check mark will appear to signal relearn completion.
10.Exit out of tire menu. Vehicle will need to be driven several minutes to complete relearn process.


Audi Q7 2007-2012 TPMS Reset Tire Pressure Monitoring System Reset
1. Inflate all tires to pressure listed on tire placard.
2. Turn ignition to ON/RUN position (engine off).
3. Press CAR function button.
4. Select TIRE PRESSURE MONITORING.
5. Select INITIALIZE WHEELS (select STORE CURR TIRE PRESSURES if resetting tire pressures).
6. Relearn can take 20 minutes to complete.


Audi Q7 2010-2015 TPMS Reset Tire Pressure Monitoring System Reset
1. Inflate all tires to pressure indicated on tire placard.
2. Turn ignition to ON/RUN position (engine off).
3. Press CAR or MENU button by the gear selector.
4. Rotate MENU knob to position arrow by SET, Tire Pressure Monitoring, or Car (depending on exact model trim).
5. Press MENU knob.
6. Move arrow to TIRE PRESSURE, only if selecting the Car option mentioned in Step 4.
7. Press MENU knob.
8. Move arrow to STORE PRESSURES.
9. Press MENU knob, a check mark will appear to signal relearn completion.
10.Exit out of tire menu. Vehicle will need to be driven several minutes to complete relearn process.


Audi R8 2008-2015 TPMS Reset Tire Pressure Monitoring System Reset
1. Inflate all tires to pressure listed on tire placard.
2. Turn ignition to ON/RUN position (engine off).
3. Press CAR function button.
4. Select TIRE PRESSURE MONITORING.
5. Select INITIALIZE WHEELS (select STORE CURR TIRE PRESSURES if resetting tire pressures).
6. Relearn can take 20 minutes to complete.


Audi R8 2013-2015 TPMS Reset Tire Pressure Monitoring System Reset
1. Inflate all tires to pressure indicated on tire placard.
2. Turn ignition to ON/RUN position (engine off).
3. Press CAR or MENU button by the gear selector.
4. Rotate MENU knob to position arrow by SET, Tire Pressure Monitoring, or Car (depending on exact model trim).
5. Press MENU knob.
6. Move arrow to TIRE PRESSURE, only if selecting the Car option mentioned in Step 4.
7. Press MENU knob.
8. Move arrow to STORE PRESSURES.
9. Press MENU knob, a check mark will appear to signal relearn completion.
10.Exit out of tire menu. Vehicle will need to be driven several minutes to complete relearn process.


Audi RS4 2007-2008 TPMS Reset Tire Pressure Monitoring System Reset
1. Inflate all tires to pressure listed on tire placard.
2. Press CAR function button, or select "SET" on the driver's information screen.
3. Select TIRE PRESSURE MONITORING.
4. Select WHEEL CHANGE (select STORE CURR TIRE PRESSURES if resetting tire pressures).
5. Relearn can take 20 minutes to complete.


Audi RS7 2014-2015 TPMS Reset Tire Pressure Monitoring System Reset
1. Inflate all tires to pressure listed on tire placard.
2. Turn ignition to ON/RUN position (engine off).
3. Press CAR function button.
4. Select TIRE PRESSURE MONITORING.
5. Select INITIALIZE WHEELS (select STORE CURR TIRE PRESSURES if resetting tire pressures).
6. Relearn can take 20 minutes to complete.


Audi S4 2004-2011 TPMS Reset Tire Pressure Monitoring System Reset
1. Inflate all tires to pressure listed on tire placard.
2. Press CAR function button, or select "SET" on the driver's information screen.
3. Select TIRE PRESSURE MONITORING.
4. Select WHEEL CHANGE (select STORE CURR TIRE PRESSURES if resetting tire pressures).
5. Relearn can take 20 minutes to complete.


Audi S8 2007-2009 TPMS Reset Tire Pressure Monitoring System Reset
1. Inflate all tires to pressure listed on tire placard.
2. Turn ignition to ON/RUN position (engine off).
3. Press CAR function button.
4. Select TIRE PRESSURE MONITORING.
5. Select INITIALIZE WHEELS (select STORE CURR TIRE PRESSURES if resetting tire pressures).
6. Relearn can take 20 minutes to complete.


Audi SQ5 2014-2015 TPMS Reset Tire Pressure Monitoring System Reset
1. Inflate all tires to pressure indicated on tire placard.
2. Turn ignition to ON/RUN position (engine off).
3. Press CAR or MENU button by the gear selector.
4. Rotate MENU knob to position arrow by SET, Tire Pressure Monitoring, or Car (depending on exact model trim).
5. Press MENU knob.
6. Move arrow to TIRE PRESSURE, only if selecting the Car option mentioned in Step 4.
7. Press MENU knob.
8. Move arrow to STORE PRESSURES.
9. Press MENU knob, a check mark will appear to signal relearn completion.
10.Exit out of tire menu. Vehicle will need to be driven several minutes to complete relearn process.


Audi TT 2008-2012 TPMS Reset Tire Pressure Monitoring System Reset
1. Inflate all tires to pressure indicated on tire placard.
2. Turn ignition to ON/RUN position (engine off).
3. Hold down the "SET" button located between the A/C and radio controls, or near the gear selector until a chime is heard.
4. Drive vehicle above 30mph for at least 30 minutes.


Audi TT 2009-2015 TPMS Reset Tire Pressure Monitoring System Reset
1. Inflate all tires to pressure indicated on tire placard.
2. Turn ignition to ON/RUN position (engine off).
3. Press CAR or MENU button by the gear selector.
4. Rotate MENU knob to position arrow by SET, Tire Pressure Monitoring, or Car (depending on exact model trim).
5. Press MENU knob.
6. Move arrow to TIRE PRESSURE, only if selecting the Car option mentioned in Step 4.
7. Press MENU knob.
8. Move arrow to STORE PRESSURES.
9. Press MENU knob, a check mark will appear to signal relearn completion.
10.Exit out of tire menu. Vehicle will need to be driven several minutes to complete relearn process.