Ford Freestar TPMS Reset Guide
The Ford Windstar is a minivan that was produced and sold by Ford from the 1994 to 2004 model years. The second minivan designed by the company, it marked the transition from rear-wheel drive to front-wheel drive layouts popularized by the Chrysler minivans. Serving as a replacement for the Ford Aerostar, the two minivans were sold concurrently for three model years until the 1997 discontinuation of the Aerostar. For the 2004 model year, the Windstar was renamed the Ford Freestar.
Although sold as part of the Ford car lineup, the Windstar followed a tradition set by the Aerostar by not having a Lincoln-Mercury counterpart, being completely unrelated to the Mercury Villager. The success of the Windstar led to the first Ford-developed Mercury minivan, the Mercury Monterey.
All Windstars, Freestars, and Monterey minivans were assembled in Oakville, Ontario, Canada at the Oakville Assembly Plant.
1.Inflate all tires to pressure listed on tire placard.
2.Turn ignition to OFF position and press and release brake pedal.
3.Cycle ignition from OFF to RUN position 3 times, ending in RUN position.
4.Press and release brake pedal.
5.Turn ignition to OFF position.
6.Cycle ignition from OFF to RUN position 3 times, ending in RUN position.
7.Horn will sound once and TPMS telltale will blink once train mode is initiated. If equipped with message center, it will display TRAIN LF TIRE. Place antennae of learn tool on sidewall of LF tire 180° from valve stem to activate sensor. Horn will sound once sensor has been recognized. Repeat step for RF, RR, and LR tires.
8.After training LR tire, the message center will display TRAINING MODE COMPLETE. If the vehicle is not equipped with the message center display, successful completion can be verified by turning the ignition to the OFF position and not hearing the horn sound. If the horn sounds, the training procedure must be repeated.
'''''''''WITH INTEGRATED KEY FOB (ACTUAL KEY CONTAINED IN KEY FOB) PUSH-BUTTON START''''''''''''''''''''''''
1.With vehicle off, press and release the brake pedal.
2.Using the push button, press and hold the button until the vehicle is in accessory mode (ACC mode). WARNING: DO NOT PUSH AND RELEASE TOO QUICKLY…PUSH--WAIT FOR SOUND--RELEASE.
3.Power off by pushing the button 1 time.
4.Repeat 2 more times, ending in ACC mode.
5.Press and release the brake pedal, then turn vehicle off.
6.Using the push button, press and hold the button until the vehicle is in accessory mode.
7.Power off by pushing the button 1 time.
8.Repeat 2 more times, ending in ACC mode.
9.Horn will sound once the TPMS telltale will blink once train mode is initiated. If equipped with message center, it will display TRAIN LF TIRE.
10.Starting at LF tire, decrease air pressure until horn chirps. Repeat procedure for remaining tires in the following order: RF, RR, and LR. If equipped with banded sensors, place antennae of learn tool on sidewall of LF tire 180° from valve stem to activate sensor. Horn will sound once sensor has been recognized. Repeat step for RF, RR, and LR tires.
11.After successfully programming the LR tire, the message center should display "TRAINING COMPLETE."
12.Inflate all tires to pressure listed on tire placard.
''''''''''''''''WITH INTELLIGENT ASSIST IGNITION SYSTEM (NO ACTUAL KEY CONTAINED IN KEY FOB)'''''''''''''''''
1.With vehicle off, press and release the brake pedal.
2.Using the push button, press once to turn on, then press again to put vehicle into ACC mode, then press again to turn vehicle off.
3.Repeat 2 more times, ending in ACC mode.
4.Press and release the brake pedal, then turn vehicle off.
5.Using the push button, press once to turn on, then press again to put vehicle into ACC mode, then press again to turn vehicle off.
6.Repeat 2 more times, ending in ACC mode.
7.Horn will sound once and TPMS telltale will blink once train mode is initiated. If equipped with message center, it will display TRAIN LF TIRE.
8.Starting at LF tire, decrease air pressure until horn chirps. Repeat procedure for remaining tires in the following order: RF, RR, and LR. If equipped with banded sensors, place antennae of learn tool on sidewall of LF tire 180° from valve stem to activate sensor. Horn will sound once sensor has been recognized. Repeat step for RF, RR, and LR tires.
9.After successfully programming the LR tire, the message center should display "TRAINING COMPLETE."
10.Inflate all tires to pressure listed on tire placard.
IF THE ABOVE TUTORIAL WILL NOT WORK., PLEASE FOLLOW THE INSTRUCTION BELOW!
1.Inflate all tires to pressure listed on tire placard. For models without message center
2.Press and hold odometer reset button until TIRE PRESSURE SET is displayed.
3.Hold button for 3 more seconds.
4.TPMS telltale will then begin to blink to signal completion of reset process. For models with message center:
5.Press and hold SETUP button until RESET FOR SYSTEM CHECK is displayed.
6.Press and hold RESET button until HOLD RESET TO RELEARN is displayed.
7.Press and hold RESET button for 3 seconds.
8.TPMS telltale and HOLD RESET TO RELEARN message will blink 3 times to signal completion
No comments:
Post a Comment